[APP]
SavePrintFile=d:\testprint.csd			; csd document for 'Save & Print'



;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[TYPE]
;
; Max Type Count is 10.
;
Type-01=SMART50, SMART
Type-02=SMART50, SMART Lite
Type-03=SMART50, SMART Rewritable
Type-04=SMART30, SMART30
Type-05=SMART30, SMART30 Rewritable
Type-06=SMART51, SMART51
Type-07=SMART51F, SMART51 Flipper
Type-08=SMART51L, SMART51 Laminator
Type-09=SMART31, SMART31



;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[PARAMETER]
Default-01=-10          ; X Position
Default-02=-20          ; Y Position (Negative value will be recognized as Positive. Positive value will be recognized as Negative.)
Default-03=4000         ; RMP +
Default-04=7000         ; RMM +
Default-05=-300         ; Total Density
Default-06=-200         ; YMC Density
Default-07=0            ; Black Density
Default-08=0            ; Overlay Density
Default-09=0            ; Y Width
Default-10=-8           ; Y Length
Default-11=3000         ; TPH Register
Default-12=6000         ; RMM -
Default-13=5000         ; RMP -
Default-14=0            ; Yellow Level
Default-15=0            ; Magenta Level
Default-16=0            ; Cyan Level
Default-17=0            ; Black Level
Default-18=2            ; Board Type
Default-19=0            ; Display Type
Default-20=0            ; Magnetic HC/LC (0:Low-Co, 1:High-Co)
Default-21=0            ; Fast Y End Position
Default-22=200          ; Fast Y Scale --> Warming Up Display (after fw ver. 1.0.52)
Default-23=16           ; Printer Type
Default-24=19           ; Magnetic Space
Default-25=69           ; MS Track 1 Start Code
Default-26=11           ; MS Track 2 Start Code
Default-27=11           ; MS Track 3 Start Code
Default-28=255          ; MS JIS II Start Code
Default-29=31           ; MS Track 1 End Code
Default-30=31           ; MS Track 2 End Code
Default-31=31           ; MS Track 3 End Code
Default-32=255          ; MS JIS II End Code
Default-33=0            ; Error Card Out (0:Front, 1:Back)
Default-34=50           ; Rotate Top
Default-35=50           ; Rotate Bottom
ExDefault-01=350        ; Card Out Delay
ExDefault-02=0          ; Ribbon (Print) Position
ExDefault-03=0          ; DCL Mode
ExDefault-04=16         ; Printer Type



;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[SMART]
EnableFileMenu=both
Default-01=-10          ; X Position
Default-02=-20          ; Y Position (Negative value will be recognized as Positive. Positive value will be recognized as Negative.)
Default-03=4000         ; RMP +
Default-04=7000         ; RMM +
Default-05=-300         ; Total Density
Default-06=-200         ; YMC Density
Default-07=0            ; Black Density
Default-08=0            ; Overlay Density
Default-09=0            ; Y Width
Default-10=-8           ; Y Length
Default-11=3000         ; TPH Register
Default-12=6000         ; RMM -
Default-13=5000         ; RMP -
Default-14=0            ; Yellow Level
Default-15=0            ; Magenta Level
Default-16=0            ; Cyan Level
Default-17=0            ; Black Level
Default-18=2            ; Board Type
Default-19=0            ; Display Type
Default-20=0            ; Magnetic HC/LC (0:Low-Co, 1:High-Co)
Default-21=0            ; Fast Y End Position
Default-22=200          ; Fast Y Scale --> Warming Up Display (after fw ver. 1.0.52)
Default-23=16           ; Printer Type
Default-24=19           ; Magnetic Space
Default-25=69           ; MS Track 1 Start Code
Default-26=11           ; MS Track 2 Start Code
Default-27=11           ; MS Track 3 Start Code
Default-28=255          ; MS JIS II Start Code
Default-29=31           ; MS Track 1 End Code
Default-30=31           ; MS Track 2 End Code
Default-31=31           ; MS Track 3 End Code
Default-32=255          ; MS JIS II End Code
Default-33=0            ; Error Card Out (0:Front, 1:Back)
Default-34=50           ; Rotate Top
Default-35=50           ; Rotate Bottom
ExDefault-01=350        ; Card Out Delay
ExDefault-02=0          ; Ribbon (Print) Position
ExDefault-03=0          ; DCL Mode
ExDefault-04=16         ; Printer Type




;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[SMART Lite]
Default-01=-10          ; X Position
Default-02=-20          ; Y Position (Negative value will be recognized as Positive. Positive value will be recognized as Negative.)
Default-03=4000         ; RMP +
Default-04=7000         ; RMM +
Default-05=-300         ; Total Density
Default-06=-200         ; YMC Density
Default-07=0            ; Black Density
Default-08=0            ; Overlay Density
Default-09=0            ; Y Width
Default-10=-8           ; Y Length
Default-11=3000         ; TPH Register
Default-12=6000         ; RMM -
Default-13=5000         ; RMP -
Default-14=0            ; Yellow Level
Default-15=0            ; Magenta Level
Default-16=0            ; Cyan Level
Default-17=0            ; Black Level
Default-18=2            ; Board Type
Default-19=0            ; Display Type
Default-20=0            ; Magnetic HC/LC (0:Low-Co, 1:High-Co)
Default-21=0            ; Fast Y End Position
Default-22=200          ; Fast Y Scale --> Warming Up Display (after fw ver. 1.0.52)
Default-23=208          ; Printer Type
Default-24=19           ; Magnetic Space
Default-25=69           ; MS Track 1 Start Code
Default-26=11           ; MS Track 2 Start Code
Default-27=11           ; MS Track 3 Start Code
Default-28=255          ; MS JIS II Start Code
Default-29=31           ; MS Track 1 End Code
Default-30=31           ; MS Track 2 End Code
Default-31=31           ; MS Track 3 End Code
Default-32=255          ; MS JIS II End Code
Default-33=0            ; Error Card Out (0:Front, 1:Back)
Default-34=50           ; Rotate Top
Default-35=50           ; Rotate Bottom
ExDefault-01=350        ; Card Out Delay
ExDefault-02=0          ; Ribbon (Print) Position
ExDefault-03=0          ; DCL Mode
ExDefault-04=208        ; Printer Type





;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[SMART Rewritable]
Default-01=-10          ; X Position
Default-02=-20          ; Y Position (Negative value will be recognized as Positive. Positive value will be recognized as Negative.)
Default-03=4000         ; RMP +
Default-04=7000         ; RMM +
Default-05=0            ; Total Density
Default-06=0            ; YMC Density
Default-07=100          ; Black Density
Default-08=0            ; Overlay Density
Default-09=0            ; Y Width
Default-10=-8           ; Y Length
Default-11=3000         ; TPH Register
Default-12=6000         ; RMM -
Default-13=5000         ; RMP -
Default-14=0            ; Yellow Level
Default-15=0            ; Magenta Level
Default-16=0            ; Cyan Level
Default-17=0            ; Black Level
Default-18=2            ; Board Type
Default-19=0            ; Display Type
Default-20=0            ; Magnetic HC/LC (0:Low-Co, 1:High-Co)
Default-21=0            ; Fast Y End Position
Default-22=200          ; Warming-Up Display
Default-23=88           ; Printer Type
Default-24=19           ; Magnetic Space
Default-25=69           ; MS Track 1 Start Code
Default-26=11           ; MS Track 2 Start Code
Default-27=11           ; MS Track 3 Start Code
Default-28=255          ; MS JIS II Start Code
Default-29=31           ; MS Track 1 End Code
Default-30=31           ; MS Track 2 End Code
Default-31=31           ; MS Track 3 End Code
Default-32=255          ; MS JIS II End Code
Default-33=0            ; Error Card Out (0:Front, 1:Back)
Default-34=50           ; Rotate Top
Default-35=50           ; Rotate Bottom
ExDefault-01=350        ; Card Out Delay
ExDefault-02=20         ; Warming Up Temperature
ExDefault-03=0          ; DCL Mode
ExDefault-04=88         ; Printer Type



[SMART30]
Default-01=-8           ; X Position
Default-02=-30          ; Y Position (Negative value will be recognized as Positive. Positive value will be recognized as Negative.)
Default-03=4000         ; RMP +
Default-04=7000         ; RMM +
Default-05=0            ; Total Density
Default-06=0            ; YMC Density
Default-07=0            ; Black Density
Default-08=0            ; Overlay Density
Default-09=-10          ; Y End Position (Y Width)
Default-10=-38          ; Y Scale (Y Length)
Default-11=3000         ; TPH Register
Default-12=6000         ; RMM -
Default-13=5000         ; RMP -
Default-14=0            ; Yellow Level
Default-15=0            ; Magenta Level
Default-16=0            ; Cyan Level
Default-17=0            ; Black Level
Default-18=2            ; Board Type
Default-19=0            ; Display Type
Default-20=0            ; Magnetic HC/LC (0:Low-Co, 1:High-Co)
Default-21=0            ; Fast Y Width
Default-22=200          ; Fast Y Scale --> Warming-Up Display (after fw ver. 1.0.52)
Default-23=65552        ; Printer Type
Default-24=19           ; Magnetic Space
Default-25=69           ; MS Track 1 Start Code
Default-26=11           ; MS Track 2 Start Code
Default-27=11           ; MS Track 3 Start Code
Default-28=255          ; MS JIS II Start Code
Default-29=31           ; MS Track 1 End Code
Default-30=31           ; MS Track 2 End Code
Default-31=31           ; MS Track 3 End Code
Default-32=255          ; MS JIS II End Code
Default-33=0            ; Error Card Out (0:Front, 1:Back)
Default-34=50           ; Rotate Top
Default-35=50           ; Rotate Bottom
ExDefault-01=350        ; Card Out Delay
ExDefault-02=0          ; Ribbon (Print) Position
ExDefault-03=0          ; DCL Mode
ExDefault-04=65552      ; Printer Type




;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[SMART30 Rewritable]
Default-01=-8           ; X Position
Default-02=-30          ; Y Position (Negative value will be recognized as Positive. Positive value will be recognized as Negative.)
Default-03=4000         ; RMP +
Default-04=7000         ; RMM +
Default-05=0            ; Total Density
Default-06=0            ; YMC Density
Default-07=0            ; Black Density
Default-08=0            ; Overlay Density
Default-09=-10          ; Y End Position (Y Width)
Default-10=-38          ; Y Scale (Y Length)
Default-11=3000         ; TPH Register
Default-12=6000         ; RMM -
Default-13=5000         ; RMP -
Default-14=0            ; Yellow Level
Default-15=0            ; Magenta Level
Default-16=0            ; Cyan Level
Default-17=0            ; Black Level
Default-18=2            ; Board Type
Default-19=0            ; Display Type
Default-20=0            ; Magnetic HC/LC (0:Low-Co, 1:High-Co)
Default-21=0            ; Fast Y Width
Default-22=200          ; Fast Y Scale --> Warming-Up Display (after fw ver. 1.0.52)
Default-23=65560        ; Printer Type
Default-24=19           ; Magnetic Space
Default-25=69           ; MS Track 1 Start Code
Default-26=11           ; MS Track 2 Start Code
Default-27=11           ; MS Track 3 Start Code
Default-28=255          ; MS JIS II Start Code
Default-29=31           ; MS Track 1 End Code
Default-30=31           ; MS Track 2 End Code
Default-31=31           ; MS Track 3 End Code
Default-32=255          ; MS JIS II End Code
Default-33=0            ; Error Card Out (0:Front, 1:Back)
Default-34=50           ; Rotate Top
Default-35=50           ; Rotate Bottom
ExDefault-01=350        ; Card Out Delay
ExDefault-02=20         ; Warming Up Temperature
ExDefault-03=0          ; DCL Mode
ExDefault-04=65560      ; Printer Type



;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

[SMART51]
EnableSecurity=yes
EnableFileMenu=both
Default-001=-5			; X Start Pos.
Default-002=2			; Y Start Pos.
Default-003=1			; Y End Pos.
Default-004=1			; Y Scale
Default-005=-300		; Total Density
Default-006=-250		; YMC Density
Default-007=450			; K Density
Default-008=300			; O Density
Default-009=4000		; RMP+
Default-010=5000		; RMP-
Default-011=7000		; RMM+
Default-012=6000		; RMM-
Default-013=-2			; Ribbon Position for Print
Default-014=0			; Delay Between Head down and Print (unit: ms)
Default-015=-28			; Flipper Angle While Rear Card Eject
Default-016=0			; Display Type
Default-017=0			; Authentification
Default-018=115200		; UART Baudrate
Default-019=0x40200		;
Default-020=0			; 
Default-021=200			; Magnetic Current by User
Default-022=0			; Magnetic Write Mode
Deafult-023=0			; 
Default-024=0x45		; 
Default-025=0x0B		; 
Default-026=0x0B		; 
Default-027=0xFF		; 
Default-028=0x1F		; 
Default-029=0x1F		; 
Default-030=0x1F		; 
Default-031=0xFF		; 
Default-032=0			; 
Default-033=0			; 
Default-034=0			; 
Default-035=0			; 
Default-036=0			; 
Default-037=0			; 
Default-038=0			; 
Default-039=0			; 
Default-040=0			; 
Default-041=0			; 
Default-042=0			; 
Default-043=0			; Cleaning Skip Count
Default-044=0			; Cleaning Count
Default-045=210			; Card In Speed
Default-046=210			; Card Eject Speed
Default-047=210			; Card Move Speed
Default-048=0			; Anti Wrinkle Line Gap
Default-049=0			; Anti Wrinkle Density
Default-050=0			; Do Cleaning Check
Default-051=0			; Card In Delay
Default-052=0x5B		; 
Default-053=0x18		; 
Default-054=0x01		; 
Default-055=0x3F		; 
Default-056=0x02		; 
Default-057=100			; Hopper Align Time
Default-071=310			; Color Registration
Default-121=0			; User Memory Block 0
Default-122=0			; User Memory Block 1
Default-123=0			; User Memory Block 2
Default-124=0			; User Memory Block 3
Default-125=0			; User Memory Block 4
Default-126=0			; User Memory Block 5
Default-127=0			; User Memory Block 6
Default-128=0			; User Memory Block 7
Default-137=3000		; Head Resister
Default-141=0			; 
Default-142=0			; 
Default-143=0			; 
Default-144=0			; 
Default-147=0			; 
Default-148=0			; 
Default-149=0			; 
Default-150=0			; 
Default-151=0			; 
Default-152=0			; 

[SMART51 Flipper]
Default-005=0			; card bin out count in User
Default-006=0			; card bin out count in factory
Default-007=0			; work count in user
Default-008=0			; work count in factory
Default-009=0			; device attribute
Default-010=210			; card in speed
Default-011=210			; card eject speed
Default-012=210			; card move speed


[SMART51 Laminator]
Default-005=700			; Max torque for film move
Default-006=500			; Min torque for film move
Default-007=1000		; Head motor torque
Default-011=0			; laminate count in user
Default-012=0			; laminate count in factory
Default-013=0			; device attribute
Default-014=210			; card in speed
Default-015=210			; card eject speed
Default-016=210			; card move speed
Default-017=390			; head resister
Default-101=150			; Film Type 0 - heater temperature
Default-102=525			;             - laminating PPS
Default-103=8250		;             - laminating move width (pulse)
Default-104=25			;             - .
Default-105=5			;             - .
Default-106=52			;             - laminating start pos on card
Default-107=700			;             - laminating film motor Max torque
Default-108=600			;             - laminating film motor Min torque
Default-109=6225		;             - laminate width (pulse)
Default-110=1			;             - film attribute
Default-111=140			; Film Type 1 - heater temperature
Default-112=525			;             - laminating PPS
Default-113=8250		;             - laminating move width (pulse)
Default-114=25			;             - .
Default-115=5			;             - .
Default-116=52			;             - laminating start pos on card
Default-117=700			;             - laminating film motor Max torque
Default-118=600			;             - laminating film motor Min torque
Default-119=6225		;             - laminate width (pulse)
Default-120=1			;             - film attribute
Default-121=150			; Film Type 2 - heater temperature
Default-122=525			;             - laminating PPS
Default-123=8250		;             - laminating move width (pulse)
Default-124=25			;             - .
Default-125=5			;             - .
Default-126=52			;             - laminating start pos on card
Default-127=700			;             - laminating film motor Max torque
Default-128=600			;             - laminating film motor Min torque
Default-129=6225		;             - laminate width (pulse)
Default-130=1			;             - film attribute
Default-131=140			; Film Type 3 - heater temperature
Default-132=525			;             - laminating PPS
Default-133=8250		;             - laminating move width (pulse)
Default-134=25			;             - .
Default-135=5			;             - .
Default-136=52			;             - laminating start pos on card
Default-137=700			;             - laminating film motor Max torque
Default-138=600			;             - laminating film motor Min torque
Default-139=6225		;             - laminate width (pulse)
Default-140=1			;             - film attribute
Default-141=105			; Film Type 4 - heater temperature
Default-142=525			;             - laminating PPS
Default-143=8250		;             - laminating move width (pulse)
Default-144=25			;             - .
Default-145=5			;             - .
Default-146=52			;             - laminating start pos on card
Default-147=700			;             - laminating film motor Max torque
Default-148=600			;             - laminating film motor Min torque
Default-149=6225		;             - laminate width (pulse)
Default-150=1			;             - film attribute
Default-151=105			; Film Type 5 - heater temperature
Default-152=525			;             - laminating PPS
Default-153=8250		;             - laminating move width (pulse)
Default-154=25			;             - .
Default-155=5			;             - .
Default-156=52			;             - laminating start pos on card
Default-157=700			;             - laminating film motor Max torque
Default-158=600			;             - laminating film motor Min torque
Default-159=6225		;             - laminate width (pulse)
Default-160=1			;             - film attribute
Default-161=105			; Film Type 6 - heater temperature
Default-162=525			;             - laminating PPS
Default-163=8250		;             - laminating move width (pulse)
Default-164=25			;             - .
Default-165=5			;             - .
Default-166=52			;             - laminating start pos on card
Default-167=700			;             - laminating film motor Max torque
Default-168=600			;             - laminating film motor Min torque
Default-169=6225		;             - laminate width (pulse)
Default-170=1			;             - film attribute
Default-171=105			; Film Type 7 - heater temperature
Default-172=525			;             - laminating PPS
Default-173=8250		;             - laminating move width (pulse)
Default-174=25			;             - .
Default-175=5			;             - .
Default-176=52			;             - laminating start pos on card
Default-177=700			;             - laminating film motor Max torque
Default-178=600			;             - laminating film motor Min torque
Default-179=6225		;             - laminate width (pulse)
Default-180=1			;             - film attribute
Default-181=105			; Film Type 8 - heater temperature
Default-182=525			;             - laminating PPS
Default-183=8250		;             - laminating move width (pulse)
Default-184=25			;             - .
Default-185=5			;             - .
Default-186=52			;             - laminating start pos on card
Default-187=600			;             - laminating film motor Max torque
Default-188=500			;             - laminating film motor Min torque
Default-189=6225		;             - laminate width (pulse)
Default-190=1			;             - film attribute
Default-191=105			; Film Type 9 - heater temperature
Default-192=525			;             - laminating PPS
Default-193=8250		;             - laminating move width (pulse)
Default-194=25			;             - .
Default-195=5			;             - .
Default-196=52			;             - laminating start pos on card
Default-197=600			;             - laminating film motor Max torque
Default-198=500			;             - laminating film motor Min torque
Default-199=6225		;             - laminate width (pulse)
Default-200=1			;             - film attribute
Default-201=105			; Film Type 10 - heater temperature
Default-202=525			;              - laminating PPS
Default-203=8250		;              - laminating move width (pulse)
Default-204=25			;              - .
Default-205=5			;              - .
Default-206=52			;              - laminating start pos on card
Default-207=600			;              - laminating film motor Max torque
Default-208=500			;              - laminating film motor Min torque
Default-209=6225		;              - laminate width (pulse)
Default-210=1			;              - film attribute
Default-211=105			; Film Type 11 - heater temperature
Default-212=525			;              - laminating PPS
Default-213=8250		;              - laminating move width (pulse)
Default-214=25			;              - .
Default-215=5			;              - .
Default-216=52			;              - laminating start pos on card
Default-217=600			;              - laminating film motor Max torque
Default-218=500			;              - laminating film motor Min torque
Default-219=6225		;              - laminate width (pulse)
Default-220=1			;              - film attribute
Default-221=170			; Film Type 12 - heater temperature
Default-222=525			;              - laminating PPS
Default-223=8250		;              - laminating move width (pulse)
Default-224=25			;              - .
Default-225=5			;              - .
Default-226=52			;              - laminating start pos on card
Default-227=600			;              - laminating film motor Max torque
Default-228=500			;              - laminating film motor Min torque
Default-229=6225		;              - laminate width (pulse)
Default-230=1			;              - film attribute
Default-231=170			; Film Type 13 - heater temperature
Default-232=525			;              - laminating PPS
Default-233=8250		;              - laminating move width (pulse)
Default-234=25			;              - .
Default-235=5			;              - .
Default-236=52			;              - laminating start pos on card
Default-237=600			;              - laminating film motor Max torque
Default-238=500			;              - laminating film motor Min torque
Default-239=6225		;              - laminate width (pulse)
Default-240=1			;              - film attribute
Default-241=170			; Film Type 14 - heater temperature
Default-242=525			;              - laminating PPS
Default-243=8250		;              - laminating move width (pulse)
Default-244=25			;              - .
Default-245=5			;              - .
Default-246=52			;              - laminating start pos on card
Default-247=600			;              - laminating film motor Max torque
Default-248=500			;              - laminating film motor Min torque
Default-249=6225		;              - laminate width (pulse)
Default-250=1			;              - film attribute
Default-251=170			; Film Type 15 - heater temperature
Default-252=525			;              - laminating PPS
Default-253=8250		;              - laminating move width (pulse)
Default-254=25			;              - .
Default-255=5			;              - .
Default-256=52			;              - laminating start pos on card
Default-257=600			;              - laminating film motor Max torque
Default-258=500			;              - laminating film motor Min torque
Default-259=6225		;              - laminate width (pulse)
Default-260=1			;              - film attribute
Default-261=170			; Film Type 16 - heater temperature
Default-262=525			;              - laminating PPS
Default-263=8250		;              - laminating move width (pulse)
Default-264=25			;              - .
Default-265=5			;              - .
Default-266=52			;              - laminating start pos on card
Default-267=600			;              - laminating film motor Max torque
Default-268=500			;              - laminating film motor Min torque
Default-269=6225		;              - laminate width (pulse)
Default-270=1			;              - film attribute
Default-271=170			; Film Type 17 - heater temperature
Default-272=525			;              - laminating PPS
Default-273=8250		;              - laminating move width (pulse)
Default-274=25			;              - .
Default-275=5			;              - .
Default-276=52			;              - laminating start pos on card
Default-277=600			;              - laminating film motor Max torque
Default-278=500			;              - laminating film motor Min torque
Default-279=6225		;              - laminate width (pulse)
Default-280=1			;              - film attribute
Default-281=170			; Film Type 18 - heater temperature
Default-282=525			;              - laminating PPS
Default-283=8250		;              - laminating move width (pulse)
Default-284=25			;              - .
Default-285=5			;              - .
Default-286=52			;              - laminating start pos on card
Default-287=600			;              - laminating film motor Max torque
Default-288=500			;              - laminating film motor Min torque
Default-289=6225		;              - laminate width (pulse)
Default-290=1			;              - film attribute
Default-291=170			; Film Type 19 - heater temperature
Default-292=525			;              - laminating PPS
Default-293=8250		;              - laminating move width (pulse)
Default-294=25			;              - .
Default-295=5			;              - .
Default-296=52			;              - laminating start pos on card
Default-297=600			;              - laminating film motor Max torque
Default-298=500			;              - laminating film motor Min torque
Default-299=6225		;              - laminate width (pulse)
Default-300=1			;              - film attribute
Default-301=170			; Film Type 20 - heater temperature
Default-302=525			;              - laminating PPS
Default-303=8250		;              - laminating move width (pulse)
Default-304=25			;              - .
Default-305=5			;              - .
Default-306=52			;              - laminating start pos on card
Default-307=600			;              - laminating film motor Max torque
Default-308=500			;              - laminating film motor Min torque
Default-309=6225		;              - laminate width (pulse)
Default-310=1			;              - film attribute
Default-311=170			; Film Type 21 - heater temperature
Default-312=525			;              - laminating PPS
Default-313=8250		;              - laminating move width (pulse)
Default-314=25			;              - .
Default-315=5			;              - .
Default-316=52			;              - laminating start pos on card
Default-317=600			;              - laminating film motor Max torque
Default-318=500			;              - laminating film motor Min torque
Default-319=6225		;              - laminate width (pulse)
Default-320=1			;              - film attribute
Default-321=170			; Film Type 22 - heater temperature
Default-322=525			;              - laminating PPS
Default-323=8250		;              - laminating move width (pulse)
Default-324=25			;              - .
Default-325=5			;              - .
Default-326=52			;              - laminating start pos on card
Default-327=600			;              - laminating film motor Max torque
Default-328=500			;              - laminating film motor Min torque
Default-329=6225		;              - laminate width (pulse)
Default-330=1			;              - film attribute
Default-331=170			; Film Type 23 - heater temperature
Default-332=525			;              - laminating PPS
Default-333=8250		;              - laminating move width (pulse)
Default-334=25			;              - .
Default-335=5			;              - .
Default-336=52			;              - laminating start pos on card
Default-337=600			;              - laminating film motor Max torque
Default-338=500			;              - laminating film motor Min torque
Default-339=6225		;              - laminate width (pulse)
Default-340=1			;              - film attribute
Default-341=170			; Film Type 24 - heater temperature
Default-342=525			;              - laminating PPS
Default-343=8250		;              - laminating move width (pulse)
Default-344=25			;              - .
Default-345=5			;              - .
Default-346=52			;              - laminating start pos on card
Default-347=600			;              - laminating film motor Max torque
Default-348=500			;              - laminating film motor Min torque
Default-349=6225		;              - laminate width (pulse)
Default-350=1			;              - film attribute
Default-351=170			; Film Type 25 - heater temperature
Default-352=525			;              - laminating PPS
Default-353=8250		;              - laminating move width (pulse)
Default-354=25			;              - .
Default-355=5			;              - .
Default-356=52			;              - laminating start pos on card
Default-357=600			;              - laminating film motor Max torque
Default-358=500			;              - laminating film motor Min torque
Default-359=6225		;              - laminate width (pulse)
Default-360=1			;              - film attribute
Default-361=170			; Film Type 26 - heater temperature
Default-362=525			;              - laminating PPS
Default-363=8250		;              - laminating move width (pulse)
Default-364=25			;              - .
Default-365=5			;              - .
Default-366=52			;              - laminating start pos on card
Default-367=600			;              - laminating film motor Max torque
Default-368=500			;              - laminating film motor Min torque
Default-369=6225		;              - laminate width (pulse)
Default-370=1			;              - film attribute
Default-371=170			; Film Type 27 - heater temperature
Default-372=525			;              - laminating PPS
Default-373=8250		;              - laminating move width (pulse)
Default-374=25			;              - .
Default-375=5			;              - .
Default-376=52			;              - laminating start pos on card
Default-377=600			;              - laminating film motor Max torque
Default-378=500			;              - laminating film motor Min torque
Default-379=6225		;              - laminate width (pulse)
Default-380=1			;              - film attribute
Default-381=170			; Film Type 28 - heater temperature
Default-382=525			;              - laminating PPS
Default-383=8250		;              - laminating move width (pulse)
Default-384=25			;              - .
Default-385=5			;              - .
Default-386=52			;              - laminating start pos on card
Default-387=600			;              - laminating film motor Max torque
Default-388=500			;              - laminating film motor Min torque
Default-389=6225		;              - laminate width (pulse)
Default-390=1			;              - film attribute
Default-391=170			; Film Type 29 - heater temperature
Default-392=525			;              - laminating PPS
Default-393=8250		;              - laminating move width (pulse)
Default-394=25			;              - .
Default-395=5			;              - .
Default-396=52			;              - laminating start pos on card
Default-397=600			;              - laminating film motor Max torque
Default-398=500			;              - laminating film motor Min torque
Default-399=6225		;              - laminate width (pulse)
Default-400=1			;              - film attribute
Default-401=-100
Default-402=-100
Default-403=-100
Default-404=0
Default-405=0
Default-406=100
Default-407=100
Default-408=0
Default-409=-100
Default-410=-200
Default-411=0
Default-412=0
Default-413=0
Default-414=0
Default-415=0
Default-416=0
Default-417=0
Default-418=0
Default-419=0
Default-420=0
Default-421=-100
Default-422=-100
Default-423=-100
Default-424=0
Default-425=0
Default-426=100
Default-427=100
Default-428=0
Default-429=-100
Default-430=-200
Default-431=0
Default-432=0
Default-433=0
Default-434=0
Default-435=0
Default-436=0
Default-437=0
Default-438=0
Default-439=0
Default-440=0
Default-441=0
Default-442=0
Default-443=0
Default-444=0
Default-445=0
Default-446=0
Default-447=0
Default-448=0
Default-449=0
Default-450=0
Default-451=0
Default-452=0
Default-453=0
Default-454=0
Default-455=0
Default-456=0
Default-457=0
Default-458=0
Default-459=0
Default-460=0

[SMART31]
Default-001=0			; X Start Pos.
Default-002=2			; Y Start Pos.
Default-003=3			; Y End Pos.
Default-004=1			; Y Scale
Default-005=-100		; Total Density
Default-006=-250		; YMC Density
Default-007=250			; K Density
Default-008=-200		; O Density
Default-009=4500		; RMP+
Default-010=5000		; RMP-
Default-011=7000		; RMM+
Default-012=6000		; RMM-
Default-013=1			; Ribbon Position for Print
Default-014=0			; Delay Between Head down and Print (unit: ms)
Default-015=-28			; Flipper Angle While Rear Card Eject
Default-016=0			; Display Type
Default-017=0			; Authentification
Default-018=115200		; UART Baudrate
Default-019=0x22200		;
Default-020=0x02		; 
Default-021=200			; Magnetic Current by User
Default-022=0			; Magnetic Write Mode
Deafult-023=0			; 
Default-024=0x45		; 
Default-025=0x0B		; 
Default-026=0x0B		; 
Default-027=0xFF		; 
Default-028=0x1F		; 
Default-029=0x1F		; 
Default-030=0x1F		; 
Default-031=0xFF		; 
Default-032=0			; 
Default-033=0			; 
Default-034=0			; 
Default-035=0			; 
Default-036=0			; 
Default-037=0			; 
Default-038=0			; 
Default-039=0			; 
Default-040=0			; 
Default-041=0			; 
Default-042=0			; 
Default-043=0			; Cleaning Skip Count
Default-044=0			; Cleaning Count
Default-045=210			; Card In Speed
Default-046=210			; Card Eject Speed
Default-047=210			; Card Move Speed
Default-048=0			; Anti Wrinkle Line Gap
Default-049=0			; Anti Wrinkle Density
Default-050=0			; Do Cleaning Check
Default-051=0			; Card In Delay
Default-052=0x5B		; 
Default-053=0x18		; 
Default-054=0x01		; 
Default-055=0x3F		; 
Default-056=0x02		; 
Default-057=100			; Hopper Align Time
Default-071=310			; Color Registration
Default-121=0			; User Memory Block 0
Default-122=0			; User Memory Block 1
Default-123=0			; User Memory Block 2
Default-124=0			; User Memory Block 3
Default-125=0			; User Memory Block 4
Default-126=0			; User Memory Block 5
Default-127=0			; User Memory Block 6
Default-128=0			; User Memory Block 7
Default-137=3000		; Head Resister
Default-141=0			; 
Default-142=0			; 
Default-143=0			; 
Default-144=0			; 
Default-147=0			; 
Default-148=0			; 
Default-149=0			; 
Default-150=0			; 
Default-151=0			; 
Default-152=0			; 
